Welcome to DTCTRUCK.COM ! Wrap new offers / gift every single day on Weekends – New Coupon code: DTCTRUCK2023
DTC-TRUCK-COM
track you order
Hotline +51900076559

My Cart -

$0.00
0
There are 0 item(s) in your cart
Subtotal: $0.00

Allison 1000 & 2000 Gen 4 Fault Codes: P0778 Pressure Control Solenoid B Electrical

Description

Allison 1000 & 2000 Gen 4 Fault Codes: P0778 Pressure Control Solenoid B Electrical

CIRCUIT DESCRIPTION:
Trim solenoid B is used to control on-coming, off-going, and holding pressure to any of the five clutches. This solenoid is referred to as a Pressure Proportional to Current (PPC) solenoid since the output hydraulic pressure supplied by this solenoid is proportional to the controlled current command.

The solenoid operates at a very high 1000 Hz frequency. Unlike the pulse width modulated Torque Converter Clutch (TCC) solenoid, where the ball follows the pulse width square wave, the PPC ball remains stationary due to the high frequency at which the solenoid operates. This allows the ball to move in a linear up and down motion proportional to the current commanded from the TCM. This supplies the desired signal pressure to control the trim valve.

CONDITIONS FOR RUNNING THE DTC:
1. The components are powered and ignition voltage is greater than 9V and less than 18V (12V TCM) or greater than 18V and less than 32V (24V TCM).
2. Engine crank time is under 4 seconds.

CONDITIONS FOR SETTING THE DTC:
DTC P0748 is set when one of the following conditions is detected for 125 milliseconds.
1. Open circuit – TCM commanded duty cycle between 31 percent and 87 percent with no current present at trim solenoid A.
2. Short to ground – TCM commanded duty cycle is over 87 percent with a current of less than 1.0 ampere at trim solenoid A.
3. Short to power – TCM commanded duty cycle is under 15 percent with electrical current present.
4. Whenever a P0748, P0778 combination is set in failure records, this is generally caused by having the transmission harness disconnected at the main transmission connector while the vehicle ignition is ON. Check the connection at the transmission and clear codes.

ACTION TAKEN WHEN THE DTC SETS:
When DTC P0778 is active, the following conditions will occur:
1. If the failure occurs while in a forward range, the transmission will shift to tst, 3rd, or 5th range.
2. If the shift selector is moved to N (Neutral), the transmission will shift to neutral.
3. If the shift selector is moved to R (Reverse), the transmission will shift to reverse.
4. If the shift selector is moved to a forward range or reverse and the transmission is compromised by overspeeding or a direction change, the transmission shifts to neutral.

DTC P0778 is stored in the TCM history.

The CHECK TRANS light illuminates.

The TCM freezes shift adapts (DNA).

CONDITIONS FOR CLEARING THE DTC/CHECK TRANS LIGHT:
A Scan Tool may be used to clear the code from the TCM history. The TCM automatically clears the DTC from the TCM history if the vehicle completes 40 warm-up cycles without the DTC recurring.

DIAGNOSTIC AIDS:
The diagnostic test performed to detect this DTC is very sensitive. Therefore, there is a high probability that an intermittent circuit condition may be causing this DTC to set. Check for the following conditions at the OEM harness first, then at the transmission internal harness.

Inspect the wiring for poor electrical connections at the TCM connector and the main transmission connector. Look for the following conditions:
1. A bent terminal.
2. A backed-out terminal.
3. A damaged terminal.
4. Poor terminal tension.
5. A chafed wire.
6. A broken wire inside the insulation.
7. Inspect OEM wiring harness routing, looking for possible contact points where chafing could occur. Moving parts on the vehicle could be contacting the harness. Check for contact at the parking brake drum, suspension components, transmission shift linkage, etc.
8. Inspect the internal transmission wiring harness for possible contact areas where chafing may occur.

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change. It may be necessary to check for shorting to ground at individual wires within a harness to isolate an intermittent condition. Refer to Wire Check information.

You may have to drive the vehicle in order to experience a fault. Use the data obtained from failure records to determine transmission range and/or certain vehicle operating variables such as temperature, run time etc. This data can be useful in reproducing the failure mode where the DTC was set.

If this DTC appears to be temperature-related, suspect a defective trim solenoid. It is possible for a trim solenoid to be temperature sensitive causing resistance values to fluctuate. This may cause an intermittent DTC to be set.

Tags: ,

Reviews

There are no reviews yet.

Be the first to review “Allison 1000 & 2000 Gen 4 Fault Codes: P0778 Pressure Control Solenoid B Electrical”

Your email address will not be published. Required fields are marked *

x